Client Guide

Coordinate systems in Georgia: WGS 84, UTM 37N and 38N, GGD

6 min read By Roman Astalavidze

Surveys in Georgia are most often done in WGS 84 / UTM, zone 37N or 38N. The zone boundary runs along 42° E: Poti and Batumi fall in zone 37N, Kutaisi and Tbilisi in zone 38N. For cadastre and topographic maps there is a national system, Georgia Geodetic Datum (GGD), and archives still contain a system based on Pulkovo 1942. Heights in state data are counted from the Baltic system, while a satellite receiver gives height above the ellipsoid.

If the system is not named in the order, the whole survey can end up shifted. Internal accuracy still looks fine, and the error shows up only when the data is laid over a design or over data from the National Agency of Public Registry (NAPR).

What a drone delivers

A drone with RTK fixes the position of its photos from satellite signals, so the original coordinates are tied to WGS 84 and heights are measured from the ellipsoid. To hand over results in GGD or a legacy system, the coordinates are transformed with official parameters, and heights are converted to a sea-level system with a geoid model. Each conversion is written into the report, because it cannot be reconstructed from the finished files.

Systems you will meet in Georgia

  • WGS 84 / UTM 37N (EPSG:32637) and 38N (EPSG:32638). The working option for most surveys. The NAPR metadata catalogue includes a dataset in EPSG:32638.
  • GGD (Georgia Geodetic Datum, EPSG:10831) on the GRS 80 ellipsoid. UTM 37N (EPSG:10836) and 38N (EPSG:10837) projections are defined for it, along with a single countrywide Lambert projection (EPSG:10833) intended for cadastre and topographic mapping. The parameters for moving between the new and old systems were published in NAPR’s 2013 methodology, prepared under an EU programme for Georgia. The EU project aimed to tie the national system to the European ETRS89.
  • The old rectangular system based on Pulkovo 1942 with a Gauss-Krüger projection. It turns up in archived drawings and plans.
  • Heights in the Baltic 1977 system (the NAPR catalogue lists EPSG:5105). These are heights above sea level, not above the ellipsoid.

Distance from coordinates versus distance from a tape

The UTM scale factor on the central meridian of a zone is 0.9996 and grows toward the edges. The central meridians of zones 37N and 38N run along 39° E and 45° E. Tbilisi sits almost on the central meridian of zone 38N and lies at about 450 m above sea level, so a distance computed from coordinates is shorter than the distance on the ground. By calculation the difference is about 5 cm per 100 m. In Batumi, 2.6° from the central meridian of zone 37N, the scale factor is above one and the coordinate distance is about 2 cm per 100 m longer. The figures are approximate: they come from the UTM scale formula for city centres.

On a 60 m building that is invisible, but on a 300 m block it already comes to about 14 cm in Tbilisi. That is why, for stake-out and as-built surveys, people ask whether dimensions are given in projected coordinates or reduced to the ground.

Heights

A receiver measures height above the ellipsoid, while designs and state data use height above sea level. The difference is called geoid height, and according to Inside GNSS it reaches about 100 m worldwide. For a site in Georgia it is taken from a geoid model, and the NAPR online service also computes quasigeoid heights. Different models give different values, so the model is named in the order. If the geoid is ignored, the whole survey is offset in height by a constant that internal accuracy will not reveal. On checking results, see Drone Survey Accuracy: RTK, Ground Control Points and RMSE Explained.

Where mistakes happen most

  • Axis order. In the EPSG registry the names of GGD projections end in (N-E): northing first, then easting. Software that expects “east, north” will place the points somewhere else.
  • The neighbouring zone. Poti lies in zone 37N and Kutaisi in 38N. A project near 42° E is run in one zone and the zone is written down.
  • Transformation parameters. NAPR publishes official parameters for GGD and the old system. Generic parameters from a software package can give noticeably worse accuracy.
  • File format. GeoTIFF and LAS store the coordinate system inside, while DXF usually does not. For DXF the system goes into the report and the file name. On formats, see What You Get After a Drone Survey: Point Cloud, LAS, GeoTIFF and DXF.

What NAPR provides

The agency runs the GEO-CORS network of continuously operating stations. EGU papers from 2017 and 2021 (the G. Khazaradze group) name 23 and 26 stations. At a UN workshop in 2012, NAPR’s Galaktion Hahubia described the network as a source of data and corrections in a single national system. The site geotransform.napr.gov.ge offers online tools for coordinate conversion, transformation between the new and old systems and computing quasigeoid heights. Terms of access to the corrections should be confirmed with NAPR.

How to state the system in an order

One line is enough, for example: “Coordinates: GGD / UTM 38N (EPSG:10837), order of writing east, north; heights: Baltic 1977 system, geoid model: model name”. If the data goes to NAPR or a municipality, confirm the system with the receiving side beforehand. If you do not know which one you need, tell us what the data is for and we will advise.

Coordinate system questions

How is GGD different from WGS 84?

GGD is Georgia’s national system on the GRS 80 ellipsoid, defined for cadastre, engineering work and topographic maps. WGS 84 is the global system that satellite receivers work in. NAPR’s 2013 methodology provides official parameters for moving between them.

How do I tell which UTM zone my site is in?

By longitude. West of 42° E it is zone 37N, east of it zone 38N. Batumi and Poti are in 37N, Tbilisi and Kutaisi in 38N.

Why do survey coordinates not match the design?

Usually it is one of three things: a different system or zone, swapped axis order, or heights given above sea level in the design and above the ellipsoid in the survey. Check them in that order.

Can old drawings be converted to WGS 84?

Yes, with NAPR’s official parameters, for example through their online service. Accuracy depends on the area and the quality of the original control, so the result is checked against checkpoints.

Which height system should be used?

The one the design uses. For state data that is most often the Baltic 1977 system. State it together with the geoid model, otherwise satellite heights have to be converted blindly.

Project Start

Request a Free Test Flight

We will survey a test area (up to 0.5 ha) of your current project free of charge. You will receive a point cloud or an orthomosaic to verify the data quality in your own CAD software before the project starts.

  • Response within one business day
  • Flight coordination accounting for airspace
  • Sample data in a format that fits your software

By submitting the form, you agree to theconditions of data processing